Ground Bond Tester Model: TOS6200

Ground Bond Tester

接地測試儀

 

Model : TOS6200

 

 

 

 

The Kikusui TOS6200

 

 

* Specification

Output block

Current setting range 3.0 Aac to 31.0 Aac x 0.1 A

(With respect to resistance resulting in output power of the maximum rated Output or less and an output terminal voltage of 5.4 V or less)

Accuracy ± (1% of setting + 0.2 A)

Maximum rated output 150 VA (at the output terminals)

Distortion factor 2% or less (with respect to 0.1 Ω pure resistance

load of 10 A or greater)

Frequency 50/60 Hz, sine wave (selectable)

Accuracy ±200 ppm

Open terminal voltage 6 Vrms or less

Output method PWM switching method

Output ammeter

Measurement range 0.0 Aac to 33.0 Aac x 0.1 A

Accuracy ± (1% of reading + 0.2 A)

Response Mean value response/rms value display (response time: 200 ms)

Holding function The current measured at the end of test is held

during the PASS or FAIL inteval

Output voltmeter

Measurement range 0.00 Vac to 6.00 Vac x 0.01 V

Accuracy ± (1% of reading + 0.02 V)

Response Mean value response/rms value display (response time: 200 ms)

Holding function The voltage measured at the end of test is held

during the PASS or FAIL inteval

Ohmmeter

Measurement range 0.001 Ω to 1.200 Ω

Resolution 0.001 Ω

Offset cancel function 0.000 Ω to 1.200 Ω (Offset ON/OFF function provided)

Accuracy ± (2% of reading + 0.003 Ω)

Holding function The resistance measured at the end of test is held

during the PASS interval

Pass/fail judgement function

Resistance value-based judgement Window comparator system

• If a resistance value equal to or greater than the upper

reference value is detected,a FAILdetermination is returned.

• If a resistance value equal to or less than the lower

reference value is detected, a FAIL determination is returned.

• If a resistance value has been judged as FAIL, the tester

shuts off the output and generates a FAIL signal.

• If the set time elapses without abnormalities, the tester

shuts off the output and generates a PASS signal.

Setting range for the upper rerence value (UPPER)

0.001 Ω to 1.200 Ω

Setting range for the upper rerence

value (LOWER)

0.001 Ω to 1.200 Ω x 0.001 Ω

Judgement accuracy ± (2% of UPPER + 0.003 Ω)

Calibration Calibration is performed with the rms value of the sine

wave, using a pure resistance load.

LED

PASS Lights for approximately 0.2 sec when the measured

value has been judged as PASS.It is lit continuously

when the PASS holding time is set to HOLD.

UPPER FAIL Lights if a resistance value equal to or greater than

the upper reference value is detected and judged FAIL.

LOWER FAIL Lights if a resistance value equal to or greater than the

upper reference value is detected and judged FAIL.

Buzzer •The buzzer sounds for the pass holding time has been

set if the measured value has been judged as PASS.

• The buzzer sounds continuously under the following

condition:

The measured value has been judged as PASS when the

PASS holding time is set to HOLD.

The measured value has been judged as UPPER FAIL.

The measured value has been judged as LOWER FAIL.

• The buzzer volume for FAIL or PASS judgment are

adjustable.

Note that it cannot be adjusted individually since setting

is shared with the setting for PASS.

Time

TimeTest 

Setting range 0.3 s to 999 s Timer ON/OFF function is available.

Accuracy ± (100ppm of setting + 20ms)

Environment

Operating environment Indoor use, Overvoltage Category II

Warranty range Temperature : 5°C to 35°C

Humidity : 20 %rh to 80 %rh (non condensing)

Operating range Temperature : 0°C to 40°C

Humidity : 20 %rh to 80 %rh (non condensing)

Storage range Temperature : -20°C to 70°C

Humidity : 90 %rh or less (non condensing)

Altitude Up to 2000 m

Power requirement

Allowable voltage range 85 Vac to 250 Vac

Power

consumption

At no load (READY) 60 VA or less

At rated load 280 VA max.

Allowable frequency range 47 Hz to 63 Hz

Insulation resistance 30 MΩ min. (500 Vdc), between AC line and chassis

Withstanding voltage 1390 Vac (2 seconds), between AC line and chassis

Earth continuity 25 Aac/ 0.1 Ω max.

Safety

Conforms to the requirements of the following directive and standard.

Low Voltage Directive 2014/35/EU, EN 61010-1 (Class I, Pollution degree 2)

Electromagnetic compatibility (EMC)

Conforms to the requirements of the following directive and standard.

EMC Directive 2014/30/EU, EN 61326-1 (Class A), EN 55011 (Class A, Group 1),

EN 61000-3-2, EN 61000-3-3

Under following conditions

1. Used test leadwire (TL11-TOS for TOS6200A, TL12-TOS for TOS6210)

which is supplied.

2. Used the shielded cable which length is less than three meters when the SIGNAL I/O is used.

Physical dimensions (maximum) 430[16.93 inch] (455[17.91 inch]) W ×

88[3.46 inch] (140[5.51 inch]) H × 270[10.63 inch] (345[13.58 inch]) D mm

Weight Approx. 9 kg (Approx.19.84 lbs)

Accessories

AC power cord 1 piece

Test leadwire TL11-TOS 1 set

Short bar 2 pieces (These are inserted between the OUTPUT

and SAMPLING terminals.)

AC power fuse 2 pieces (2, including one spare in the fuse holder)

Operation manual 1 copy